Roll-Line Giotto FreeStyle Wheels (Set of 8, 57mm)

Description

IOTTO 47D, 49
D, 53D, 57D, & 60D – 57mm
Professional FreeStyle Wheels
Hardness:  Blue=47D, Grey=49D, Cream=53D, Yellow=57D, & White=60D
Diameter:  57mm
Compound:   MonoCompound Elastomeric ThermoPlastiche Formula
The Giotto 57mm Professional FreeStyle Wheels provides a less expensive (than the Urethane counterparts), yet, very high quality wheel, which is used on many types of skating surfaces including standard wood floors coated with plastic or poly urethane, but also unusual surfaces like, tile type basketball and volleyball courts, tennis courts (Indoor or outdoor), and concrete or terrazzo surfaces that are more common around the World. The Giotto FreeStyle Wheels are used a great deal internationally, where there are few indoor skating centers like there are here in the USA. The Giotto FreeStyle wheels are most often used on abusive surfaces where the life expectancy of the wheels on these tough surfaces are not very long, but very High Skating Quality both Grip and Roll are required. Many of the world level FreeStyle competitors use combinations of hardnesses of the Giotto to achieve the best Skating result.  The Roll-Line Giotto Professional FreeStyle Wheels are Lo- Profile, reasonably durable wheel which is Strong, Light, and with extremely Close Tolerances for Roundness, Trueness, and for the Cage where the Bearings and Spacers are mounted. The Roll-Line Giotto FreeStyle Wheels are a MonoCompound Elastomeric ThermoPlastiche wheel, which is produced utilizing an injection system and is Silver Chromed.
The softer the wheel, or lower Shore “D” hardness number, the more the grip and slightly less roll. The harder the wheel, or higher Shore “D” number, the more the roll, with slightly less grip.
It is almost always recommended to use spacers in the wheels, when using standard 7mm bearings. Long ago, before the use of Lock Nuts (the nuts that have the Nylon Plastic inserts) to hold the wheels on the axles, Jam Nuts were used, but when the spacer was not as wide as the web of the wheel, or the wheel was not machined accurately, the bearings would lock up, the nut had to be tight, and could not be “backed-off”. This method, of locking the Axle Nut down, did promote proper bearing alignment and did increase the diameter of the axle from 7mm to approximately 14mm, because everything was locked down, which also saved the problems of bent axles. Today we do use Lock Nuts. It is still very advisable to lock everything down
(especially for FreeStyle, Jam, and Roller Derby Skaters)
. Roll-Line does provide Spacers for Roll-Line Wheels with each pair of Frames or they can be purchased separately. Properly locking the Wheels down when using standard bearing types, will also promote longer bearing life.
The
Roll-Line
7mm
SpeedRace
&
SpeedMax Bearings
, are specifically made for very High Level Competitive FreeStyle Roller Skating and are a very
Durable
Bearing with lots of
ROLL
. The
SpeedRace
&
SpeedMax
Bearings
are Free Rolling with minimal Radial Play which promotes and very evenly distributes the load across the 7 or 8 (of the SpeedMax) balls for optimal Roll and a good amount of Axial Play or Thrust, which is the side movement of the inner race in relation to the outer race. This movement is very important because when Skaters push, we always put side load on the skate to get power in the push or stroke. If the Bearing does not allow for this, it will bind and LOOSE operating speed or ROLL. These provisions in the Race Curvature and Contact Angle allow the
Roll-Line
SpeedRace
&
SpeedMax
Bearings
to ROLL very freely
The
Roll-Line
SpeedRace
Bearings
have 7 balls and a rubber sealant Shield and the
SpeedMax
have 8 balls and a metal Shield and are ONLY available for 7mm Axles. The
Roll-Line
SpeedRace
&
SpeedMax
Bearings
are skated on by most of the World level FreeStyle Skaters and Champions